CradlePoint MBR1200 Login: IP & Password

Log in to the CradlePoint MBR1200 at 192.168.0.1 with a blank username and the last MAC digits as the password, and fix the login faults owners hit most often.

I have set up plenty of small-business routers, and the CradlePoint MBR1200 trips owners up in one specific way. The login page asks for a password, but the router never shipped with a shared one, so owners type admin and get locked out. Your mobile broadband router is online, the settings sit one login away, and the page gives no clue what it wants.

This guide gives you the MBR1200 login, the setup steps, and the fixes that get you in.

The CradlePoint MBR1200 has no shared default password. Log in at 192.168.0.1 with a blank username and the last 6 digits of the MAC address printed on the label on the bottom of the router.

The fastest way in: tap the button below, then sign in with the password from the label on the bottom of your router.

🔐 CradlePoint MBR1200 Admin Login

IP Address: 192.168.0.1

Username: — (blank)

Password: Last 6 digits of MAC address (on label)

WiFi Name (SSID): MBR1200-xxx

Login to Admin Panel →

This button opens our 192.168.0.1 login guide, which takes you to the router itself. It works only when your device is connected to that router, by WiFi or cable.

How to Log in to the CradlePoint MBR1200

Read the password off the label first, so you are not guessing at the login screen.

  1. Power the MBR1200 and wait for it to finish booting, then connect your computer by cable or join its Wi-Fi network.
  2. Find the MAC address on the label on the bottom of the router and note its last 6 digits.
  3. Open a browser and go to 192.168.0.1. You can also type cp/ in the address bar. Type the address into the address bar, not the search bar.
  4. Leave the username blank, type the last 6 digits of the MAC address as the password, and click Login.
  5. The admin panel opens. On a first login the First Time Setup Wizard walks you through the basic settings.
CradlePoint MBR1200 login laptop desk setup wifirouterzone.com
Join the router’s Wi-Fi first, then open the admin panel.

CradlePoint MBR1200 Default Username and Password

I have seen this catch owners out: login sites list admin and admin for the MBR1200, and that is wrong. The MBR1200 user manual says the default administrative password is the last 6 digits of the MAC address on the label, so use the table below.

ModelUsernamePasswordLogin IP
MBR1200— (blank)Last 6 digits of MAC address (on label)192.168.0.1
MBR1200B— (blank)Last 8 characters of MAC address (on label)192.168.0.1

The MBR1200B is the later version of the same router, and its quick start guide gives the last 8 characters of the MAC address instead of 6. Check which model is printed on your label, then use the matching row.

CradlePoint also says routers made from December 2018 onward use the serial number as the default password, so check the label if the MAC digits do not work.

Change CradlePoint MBR1200 WiFi Password and Network Name

On the MBR1200 the Wi-Fi security settings sit apart from the admin login, so change them in the same visit.

  1. Log in at 192.168.0.1 with the password from the label.
  2. Open the BASIC tab, then the Setup Wizard, and click NEXT until you reach the Wi-Fi security step.
  3. Type your new network name (SSID) in the network name box.
  4. Choose a Wi-Fi security password of at least 12 characters and type it in.
  5. Save the settings, then reconnect your devices with the new password.

Use a password of at least 12 characters with letters and numbers, and do not reuse a password from anywhere else.

CradlePoint MBR1200 Login Not Working?

  • Make sure your device is connected to the MBR1200 network, not to mobile data or a different Wi-Fi network.
  • Type 192.168.0.1 exactly, with no extra letters or spaces. Try http://192.168.0.1 if the page will not load, or type cp/ instead.
  • Do not type admin as the password. The password is the last 6 digits of the MAC address on the bottom label.
  • Check that Caps Lock is off, and type the password exactly as it is — passwords are case-sensitive.
  • Restart the router: unplug it, wait 30 seconds, and plug it back in.

If you still cannot log in because the password was changed and forgotten, reset the router to factory settings: let it finish booting, then hold the reset button for about 10 seconds and let go. After the reset, the password is the label password again.

Once you are in, our port-forwarding guide shows the next setup step for cameras and remote access.

The MBR1200 is a small-business mobile broadband router with 802.11n Wi-Fi, a Gigabit Ethernet WAN port, and USB and ExpressCard slots for a 3G or 4G modem. Its internal antennas reach up to 600 feet, and it supports VPN tunnels for remote offices.

Cradlepoint MBR1200 problems users report, and what fixed them

“Carrier Reject” after every restart

A Verizon customer’s UML295 modem worked the first time in an MBR1200, then showed Carrier Reject after each reboot, across 3 SIMs and 2 routers. Check the firmware release notes for your modem before updating.

LTE modem drops several times a day

An MBR1200 owner with a UML290 had daily disconnects. Updating the modem’s own firmware also brought an LTE connection where only 3G had worked before.

Modem works as primary but not as failover

Cradlepoint firmware notes list modems that fail to connect in failover mode, and a fix for some address conflicts: put the modem on a USB extension cable.

FAQs About CradlePoint MBR1200 Login

The default password is the last 6 digits of the MAC address printed on the label on the bottom of the router. There is no shared password, so admin will not work. I read the digits off the label before I open the login page.

The default IP is 192.168.0.1. Type http://192.168.0.1 in the browser address bar while connected to the router, by Wi-Fi or cable. You can also type cp/ as the address.

Leave the username blank. The login page only asks for the password, which is the last 6 digits of the MAC address on the label.

The default Wi-Fi name is MBR1200-xxx, where the last part matches your unit. The Wi-Fi password is the same label password you use for the admin login, unless you changed it during setup.

Let the router finish booting, then hold the reset button for about 10 seconds and let go. After the reset, log in at 192.168.0.1 with the last 6 digits of the MAC address from the label.

The team behind this guide
Grace Muller

Grace Muller found this topic
Content Strategist
Focus: Topic Planning & Coverage

Marcus Lee

Marcus Lee wrote this guide
Content Writer · Published November 19, 2026
Focus: ISP & Modem Routers

Nina Petrova

Nina Petrova designed the visuals
Graphic Designer
Focus: Brand & Illustrations

Awais

Awais verified the facts
Founder & Editor-in-Chief · Last verified: November 2026
Focus: Final fact-check & publishing

Similar Posts