Edgewater Router Login: Default IP & Password
Log in to an Edgewater EdgeMarc router at 192.168.1.1 with the username root and the password default, and fix the login faults owners hit most often.
I have configured Edgewater EdgeMarc units for small offices, and the login surprises everyone the first time. The username is root, not admin, and the password is the word default. These are business session border controllers, not home routers, so the whole login works differently from the brands most people know.
This guide gives you the Edgewater login, the EdgeMarc model table, and the steps that get you in.
Edgewater EdgeMarc routers log in at 192.168.1.1 with the username root and the password default. That pair comes straight from Edgewater’s own installation guides for the 200AW, 250W, 4200 and 4500 models.
The fastest way in: tap the button below, then sign in with the details in the box.
IP Address: 192.168.1.1
Username: root
Password: default
Login to Admin Panel →This button opens our 192.168.1.1 login guide, which takes you to the router itself. It works only when your device is connected to that router, by cable. EdgeMarc units are wired devices, so use a LAN port, not Wi-Fi.
How to Log in to a Edgewater Router
Give your computer a static address first, because the EdgeMarc expects it.
- Connect your computer to LAN port 1 of the EdgeMarc with an Ethernet cable.
- Set your computer to the static address 192.168.1.2 with the subnet mask 255.255.255.0 and the gateway 192.168.1.1.
- Open a browser and go to 192.168.1.1.
- Type root in the username field and default in the password field, then click Login.
- The System page opens, and you can change the admin password or check the VoIP and network settings.

Edgewater Default Username and Password
I have seen this catch owners out: every EdgeMarc model uses the same login, but the SSH password is different again. The table below lists the models I could verify from the installation guides, so find yours and try its row first.
| Model | Username | Password | Login IP |
|---|---|---|---|
| EdgeMarc 200AW / 200AE2 | root | default | 192.168.1.1 |
| EdgeMarc 250W / 250AE | root | default | 192.168.1.1 |
| EdgeMarc 4200 | root | default | 192.168.1.1 |
| EdgeMarc 4500 / 4500T4 | root | default | 192.168.1.1 |
| EdgeMarc 4550 / 4552 / 4700 | root | default | 192.168.1.1 |
| EdgeMarc CLI (SSH only) | root | @#$%^&*!90 | 192.168.1.1 |
The SSH password is only for the command line, and it is not the web password — do not type it into the browser login. The default Wi-Fi name on the few wireless EdgeMarc units starts with EDGEXXX, so check the label if you are unsure which network is yours.
The same login covers the whole EdgeMarc line, which is rare and worth knowing. Whether the box says 200AW or 4700, the first login is root and default, and the first job is always to change it. I never leave a business gateway on a password that is printed in the manual.
Change Edgewater WiFi Password and Network Name
Most EdgeMarc units are wired session border controllers with no Wi-Fi radio at all, so there is often no Wi-Fi password to change. I check the model first, because the steps below only apply to EdgeMarc units that ship with wireless.
- Log in at 192.168.1.1 with root and default.
- Open the Network settings in the admin panel.
- Find the wireless section and type your new network name (SSID) in the network name box.
- Set the security to WPA2, then type a new Wi-Fi password.
- Save the settings, then reconnect your devices with the new password.
The first job after any EdgeMarc login is the admin password, not the Wi-Fi. Open the Change Administrative Password section on the System page and set a strong new password right away, because root and default is printed in every manual.
If the unit has no wireless section, that is by design, not a fault. EdgeMarc units guard voice traffic on a wired network, and the Wi-Fi, where it exists, is a side feature. The admin password change matters far more than any wireless setting.
Edgewater Login Not Working?
- Make sure your computer is on LAN port 1 with the static address 192.168.1.2, not on DHCP from another network.
- Check that the WAN cable is plugged into the port labelled WAN, and that you are on a LAN port.
- Try root and default, not admin and admin — EdgeMarc has never used admin as a username.
- If the web login fails but SSH works, you are typing the CLI password into the wrong box.
- Check that Caps Lock is off, and type the password exactly as it is — passwords are case-sensitive.
- Restart the unit: unplug it, wait 30 seconds, and plug it back in.
If you still cannot log in because the password was changed and forgotten, reset the router to factory settings with the Erase button: press it three times in quick succession and the EdgeMarc reverts to factory defaults, erases all settings, and returns to 192.168.1.1 with root and default.
Pressing Erase twice only resets the CLI password, so count the presses. If the login page will not open at all, check that you are using the right gateway address with our router IP finder.
Edgewater is the brand where the username matters most. Type root, type default, and the System page opens — admin was never the answer here. Change the password on day one, and the gateway is yours alone.
Edgewater problems users report, and what fixed them
Which login does an EdgeMarc use
Ribbon, which now owns Edgewater, documents root as the username and default as the password at 192.168.1.1, and the router asks you to set a new password after the first login. See Ribbon: EdgeMarc first login.
root and default stopped working
Once the password has been changed on first login, the default no longer applies. A factory reset is the only way back if nobody saved the new one.
My VoIP provider configured the router
8×8 customers load an 8×8 QoS config file on EdgeMarc routers. Ask your provider before resetting, because a reset removes that config. See 8×8: EdgeMarc router configuration.










