D-Link DIR-300 Rev A1 Login: IP & Password

The DIR-300 Rev A1’s password box stays empty at first login. This guide walks you step by step through setup, WiFi changes, resets, and fixes.

You have a D-Link DIR-300 Rev A1 on the shelf, and the login asks for a password nobody wrote down. I have set up DIR-300 routers, and the first login trips owners up every time: the username is admin, and the password box stays empty. This guide walks you through the login, the Wi-Fi change, and the reset.

This guide gives you the DIR-300 Rev A1 login, the variant table, and the steps that get you in.

The D-Link DIR-300 Rev A1 logs in at 192.168.0.1 with the username admin and a blank password. Type the address into your browser, enter admin, leave the password box empty, and the setup wizard opens.

The fastest way in: tap the button below, then sign in with the details in the box.

🔐 D-Link DIR-300 Rev A1 Admin Login

IP Address: 192.168.0.1

Username: admin

Password: (blank — leave empty)

Login to Admin Panel →

This button opens our 192.168.0.1 login guide, which takes you to the router itself. It works only when your device is connected to that router, by WiFi or cable. If your unit is a DIR-300A or an NRU B-series, use admin and admin from the table below instead.

How to Log in to the D-Link DIR-300 Rev A1

Connect by cable first, because the setup wizard works best over a wired connection.

  1. Connect your computer to a LAN port on the DIR-300 with the Ethernet cable from the box.
  2. Open a browser and go to 192.168.0.1. Type the address into the address bar, not the search bar.
  3. Type admin in the username field and leave the password field blank, then click Log In.
  4. The setup wizard opens. Pick your connection type — Dynamic IP, PPPoE, PPTP or L2TP — from your ISP’s details.
  5. Finish the wizard, then set your wireless network name and password before you go further.
D-Link DIR-300 Rev A1 login network switch ports wifirouterzone.com
Connect by cable before you open the login page — the setup wizard works best over a wired connection.

D-Link DIR-300 Rev A1 Default Username and Password

I have seen this catch owners out: later DIR-300 revisions use a password, but the Rev A1 ships with the password blank. The table below lists every variant I could verify from the D-Link manuals, so find yours and try its row first.

ModelUsernamePasswordLogin IP
DIR-300 Rev A1admin(blank)192.168.0.1
DIR-300A (regional)adminadmin192.168.0.1
DIR-300 NRU B1 / B2 / B3 (reported)adminadmin192.168.0.1

If your revision is not in the table, start with admin and a blank password at 192.168.0.1. That is the pair the D-Link user manual prints for the DIR-300, and it is the revision most owners have at home. The label on the bottom of the router is the final word if the pair fails.

The admin and admin pair belongs to the regional DIR-300A and the NRU B-series, not to the Rev A1. I keep the two apart, because typing admin as the password is the most common reason the Rev A1 login fails.

Change D-Link DIR-300 Rev A1 WiFi Password and Network Name

I change the Wi-Fi password first on every router I set up, because the factory network has no password at all. Once you are logged in, the change takes about a minute.

  1. Log in at 192.168.0.1 with admin and a blank password.
  2. Open the Wireless Setup section in the admin panel.
  3. Type your new network name (SSID) in the network name box and save it.
  4. Set the security to WPA or WPA2, then type a new Wi-Fi password.
  5. Save the settings, then reconnect your devices with the new password.

The DIR-300 ships with WEP and WPA security, and I pick WPA2 when the menu offers it. WEP is too weak to trust with anything that matters, so I never leave it on.

If the wireless menu asks for a setup wizard, run it — the DIR-300 wizard covers the wireless settings in a few screens. Our WiFi settings guide covers the same steps in detail.

D-Link DIR-300 Rev A1 Login Not Working?

  • Make sure your device is connected to the DIR-300 network, not to mobile data or a different Wi-Fi network.
  • Check that the modem cable is plugged into the port labelled INTERNET, and that you are on a LAN port or the DIR-300 Wi-Fi.
  • Leave the password blank. Admin and admin belongs to the DIR-300A and the NRU B-series, not to the Rev A1.
  • Try 192.168.0.1 first. A few ISP-supplied units answer at 192.168.1.1 instead.
  • Check that Caps Lock is off, and type the password exactly as it is — passwords are case-sensitive.
  • Restart the router: unplug it, wait 30 seconds, and plug it back in.

If you still cannot log in because you changed the password and forgot it, reset the router to factory settings: press the reset button on the rear panel with a paper clip and hold it for 10 seconds, then let go.

The router reboots in about 30 seconds, and the login returns to admin with a blank password.

A reset erases every setting, and the router will ask you to set it up again. If the login page will not open at all, check that you are using the right gateway address for your unit.

D-Link DIR-300 Rev A1 Key Specs

The DIR-300 Rev A1 is a Wireless G router from 2007. It pairs an 802.11g wireless radio at up to 54 Mbps with a 4-port 10/100 switch and one WAN port for the modem, and it runs the web-based setup wizard for the internet connection.

The wireless side supports WEP and WPA/WPA2 security, and the admin panel covers the connection types most ISPs used at the time: Dynamic IP, PPPoE, PPTP and L2TP. The unit has no USB port and no 5 GHz radio, so it suits a small home with a basic broadband line.

It shipped in 2007, so it is long out of support. I treat any DIR-300 still in service as a legacy device and plan its replacement rather than relying on it for new security work.

The Rev A1 is the router where the empty password matters most. Type admin, leave the password blank, and the wizard opens at 192.168.0.1. Set a password on day one, and the router is yours alone.

FAQs About D-Link DIR-300 Rev A1 Login

The default password is blank — leave the password box empty. D-Link’s own user manual says to enter the username admin and leave the password blank by default. The admin and admin pair belongs to the regional DIR-300A and the NRU B-series, not to the Rev A1.

The DIR-300 Rev A1 uses 192.168.0.1, and that is the address the D-Link manual prints. I connect by cable to a LAN port first, then type the address into the browser’s address bar, not the search bar.

Admin and admin belongs to the DIR-300A and the NRU B-series, not to the Rev A1. The Rev A1 logs in with the username admin and a blank password, so typing admin into the password box is what makes it fail.

Log in at 192.168.0.1 with admin and a blank password, open the Wireless Setup section, and set a new WPA2 password. I write the new password down before I save it, so I am not locked out of my own wireless network.

Press the reset button on the rear panel with a paper clip and hold it for 10 seconds, then let go. The router reboots in about 30 seconds, and the login returns to admin with a blank password. A reset erases every setting, so you will need to set the router up again.

The team behind this guide
Grace Muller

Grace Muller found this topic
Content Strategist
Focus: Topic Planning & Coverage

Anna Kowalski

Anna Kowalski wrote this guide
Content Writer · Published November 22, 2026
Focus: Troubleshooting & Fixes

Nina Petrova

Nina Petrova designed the visuals
Graphic Designer
Focus: Brand & Illustrations

Awais

Awais verified the facts
Founder & Editor-in-Chief · Last verified: November 2026
Focus: Final fact-check & publishing

Similar Posts