NETGEAR Nighthawk R6700 Login: Admin Setup Guide
The first time I set up a Nighthawk R6700, the login page kept rejecting the…
The first time I set up a Nighthawk R6700, the login page kept rejecting the password I was certain was right. I have been in that spot before: the router is working, the settings are one password away, and the page gives you no hint about what is wrong.
This guide gives you the correct defaults for the Nighthawk R6700 and the four steps that will get you into the admin panel.
Log in at 192.168.1.1 with the username admin and the password password.
The fastest way in: tap the button below, then sign in with the details in the box.
IP Address: 192.168.1.1
Username: admin
Password: password
Login to Admin Panel →This button opens your router’s own login page. It works only when your device is connected to this router, by WiFi or cable.
NETGEAR Nighthawk R6700 Default Login Details
I checked these defaults against the R6700 setup flow before I wrote them down, so the table below matches the router you have in front of you.
These are the factory defaults for the Nighthawk R6700, taken from the official NETGEAR manual: after a reset the user name is admin, the password is password, and the LAN IP address is 192.168.1.1. Keep them somewhere safe once you have logged in, and change the admin password to something only you know.
| Detail | Value |
|---|---|
| Login IP | 192.168.1.1 |
| Username | admin |
| Password | password |
How to Log In to the NETGEAR Nighthawk R6700
I walk through this in the same order every time, because the order is what keeps a login from going wrong. If your router asks you to create a password instead, the NETGEAR login guide covers that first-setup flow too.
- Connect your computer or phone to the Nighthawk R6700 with an Ethernet cable or over Wi-Fi.
- Open a browser and go to 192.168.1.1. You can also open routerlogin.net, which takes you to the same login page.
- Type admin in the username field and password in the password field.
- Click Log In. The admin panel opens, and you can change the Wi-Fi name and password, update the firmware, or check connected devices.
Default Username and Password — All Variants
I have seen this catch owners out: the same model can ask for a fixed password on one firmware and ask you to create one on another, so check which case matches your router.
The R6700 family shares the same factory defaults, with one difference on later revisions. Check which case matches your router:
| Version | Username | Password |
|---|---|---|
| R6700 | admin | password |
| R6700v2 | admin | password — identical defaults to the R6700 |
| Later revisions, e.g. R6700v3 | admin | May prompt you to set an admin password at first setup instead |
If your R6700 revision asks you to set an admin password the first time you log in, that password becomes the new admin password, so choose one you will remember.
Change WiFi Password and Network Name
I change the Wi-Fi password first on every router I set up, because the factory password is the same on every unit that leaves the shop.
Once you are logged in to the Nighthawk R6700 admin panel, changing the Wi-Fi details takes about a minute:
- Log in at 192.168.1.1 with the admin password.
- Open the Wireless settings section of the admin panel.
- Change the network name (SSID) for the 2.4 GHz and 5 GHz bands, or leave it as it is.
- Type a new Wi-Fi password, then save the settings.
- Reconnect your devices with the new password.
Use a password of at least 12 characters with a mix of letters and numbers, and avoid reusing a password you use anywhere else.
Login Not Working?
I start with the connection itself, because that is where most login failures begin, and I work through the list in the order it is written.
If the login page will not open or the password is rejected, work through these fixes:
- Make sure your device is connected to the Nighthawk R6700 network, not to mobile data or a different Wi-Fi network.
- Type the address exactly: http://192.168.1.1, with no extra letters or spaces. Try routerlogin.net if the IP does not load.
- Try a different browser, or clear the browser cache and try again.
- Check that Caps Lock is off, and type the password exactly as it is — passwords are case-sensitive. Remember that the default password is the word password, not the name of the router.
- Restart the router: unplug it, wait 30 seconds, and plug it back in.
If you still cannot log in because the password was changed and forgotten, reset the router to factory settings: using a straightened paper clip, press and hold the Reset button for at least 5 seconds. After the reset, log in again with the factory defaults above, and set up the router from scratch.
Key specs: The NETGEAR Nighthawk R6700 is a WiFi 5 (AC1750) dual-band router.
