Rogers Router Login: IP, Username and Password
Log in to Rogers at 10.0.0.1 or 192.168.0.1. Ignite and Hitron defaults, WiFi, bridge mode and reset.
Connect to your Rogers router first by WiFi or cable. Older Rogers Hitron modems use 192.168.0.1.
Rogers Ignite gateways open their admin page at 10.0.0.1, while older Rogers Hitron modems use 192.168.0.1. Many settings, including WiFi, are also in the Ignite HomeConnect or Rogers app.
This guide covers both gateway types, the default logins and how to change WiFi, use bridge mode and reset.
The fastest way in: tap the login button in the box at the top of this page, then sign in with the details on your router label.
How to log in to your Rogers router
- Connect your phone or computer to the modem WiFi, or plug in an Ethernet cable.
- Open a browser and type http://10.0.0.1 in the address bar. Older Hitron modems use http://192.168.0.1.
- Enter the admin username and password from the label or the table below.
- Once logged in, change the admin password and check that WiFi security is WPA2 or WPA3.
If the page does not open, check your Default Gateway with our Router IP Finder. ISP builds sometimes use a different address.
The Ethernet-cable step is the one I try first when the login page will not open.
Rogers default IP, username and password
| Device | Login address | Username | Password |
|---|---|---|---|
| Rogers Ignite gateway (XB6, XB7, XB8) | 10.0.0.1 | admin | password, change required |
| Rogers Hitron CODA / CGN3 | 192.168.0.1 | cusadmin | password or label |
| After setup | Same | admin or cusadmin | Your own password |
If the defaults fail, the password was changed. Use the app or a reset. The label-first check is the habit I keep before I trust any default. On Hitron modems, the Easy Connect Wi-Fi password on the label also works as the login password.
How to change the WiFi password on a Rogers router
- Log in to the gateway or open the Rogers app.
- Go to Gateway, Connection, Wi-Fi (Ignite) or Wireless (Hitron).
- Edit the network name and password and save.
- Reconnect your devices.
In the app, open WiFi and tap Edit. Need a strong key? Try our WiFi Password Generator. For me, the app route is the quickest way to change a WiFi password.
Rogers bridge mode
Ignite gateways: Gateway, At a Glance, Bridge Mode, Enable. Hitron modems: Basic, Gateway Function, turn off Residential Gateway Function. Then connect your own router.
In bridge mode, the gateway WiFi turns off and your router takes over. The double-NAT check is the reason I confirm bridge mode actually took.
Rogers login problems and fixes
- 10.0.0.1 will not load: make sure you are on the router WiFi, not mobile data or a VPN, and type http:// in front.
- Wrong password: check the label first. If you or your ISP changed it, the defaults will not work.
- Page loads but login fails: clear the browser cache or try a private window. Some routers lock you out for a few minutes after several attempts.
- Router from your ISP: the provider may manage it. Their app or support line can reset the admin password.
- Still locked out: a factory reset restores the label login, but erases your settings.
I start with the wrong-password case whenever a Rogers login fails.
How to reset a Rogers router
- Keep the modem powered on.
- Press and hold the reset button for about 30 seconds.
- Release and wait several minutes while it restarts and reconnects.
- Log in with the label details and set up WiFi again.
Hold for 30 seconds for a full factory reset on Ignite and Hitron units. When I reset a gateway, the 30-second hold is the step I never rush.
Rogers Ignite WiFi Gateway
Rogers Ignite customers usually have the Ignite WiFi Gateway (based on the same XB6, XB7 and XB8 hardware Comcast uses). It opens at 10.0.0.1, starting with admin/password, and asks you to set your own password on first login.
Rogers also offers Ignite WiFi Pods for extra coverage, managed in the Rogers app. The first-login password prompt is the detail I warn new Ignite owners about.
Turn on bridge mode on a Rogers gateway
- Log in at 10.0.0.1.
- Go to Gateway, then At a Glance.
- Set Bridge Mode to Enable and confirm.
- Wait for the gateway to restart.
- Connect your own router to the gateway’s Ethernet port.
Ignite TV boxes connect over WiFi or Ethernet to your network and work fine behind your own router in most cases.
The restart wait is the part I remind people about after bridge mode is on.
Rogers 5G and Ignite internet
Rogers offers wired Ignite internet and 5G Home Internet in some areas. 5G Home uses a different gateway with its own login and app. If you have a 5G gateway, place it near a window facing the nearest tower and check signal in its app.
The window-facing spot is the placement tip I give first for any 5G gateway.
Rogers gateway lights
- White: working normally.
- Flashing: starting up or updating.
- Amber or red: no internet. Restart and check cables.
My first look is always the light color, since it says more than the app does.
