Digisol Router Login: Router Admin Setup Guide
Log in to Digisol at 192.168.1.1 or 192.168.2.1 with admin and admin.
Connect to your Digisol router first by WiFi or cable. Some Digisol models use 192.168.2.1.
Digisol routers, popular in India, open their settings at 192.168.1.1 on most models and 192.168.2.1 on some others.
The default login is usually admin and admin. ISP-supplied units may print a unique password on the label. Here is how to log in, change WiFi and reset.
The fastest way in: tap the login button in the box at the top of this page, then sign in with the details on your router label.
How to log in to your Digisol router
- Connect your phone or computer to the router WiFi, or plug in an Ethernet cable.
- Open a browser and type http://192.168.1.1 in the address bar. Some models use http://192.168.2.1.
- Enter the username and password from the table below or the router label.
- Once logged in, change the admin password and use WPA2 or WPA3 for WiFi.
If the page does not open, check your Default Gateway with our Router IP Finder. ISP builds sometimes use a different address.
Digisol default IP, username and password
| Model or type | Login address | Username | Password |
|---|---|---|---|
| Most Digisol routers | 192.168.1.1 | admin | admin |
| Some DG-HR series | 192.168.2.1 | admin | admin |
| ISP-supplied units | See label | admin | On the label |
If admin fails, check the label or reset the router.
How to change the WiFi password on a Digisol router
- Log in to the router.
- Open Wireless, then Security.
- Choose WPA2-PSK and set a new passphrase.
- Save and reconnect devices.
Change both bands on dual-band models. Need a strong key? Try our WiFi Password Generator.
Digisol login problems and fixes
- 192.168.1.1 will not load: make sure you are on the router WiFi, not mobile data or a VPN, and type http:// in front.
- Wrong password: check the label first. If you or your ISP changed it, the defaults will not work.
- Page loads but login fails: clear the browser cache or try a private window. Some routers lock you out for a few minutes after several attempts.
- Router from your ISP: the provider may manage it. Their app or support line can reset the admin password.
- Still locked out: a factory reset restores the label login, but erases your settings.
How to reset a Digisol router
- Keep the router powered on.
- Press and hold the reset button for about 5 to 10 seconds, until the lights flash.
- Release and wait 2 to 3 minutes.
- Log in with the default details and set up WiFi again.
Note your ISP PPPoE login before resetting.
Digisol routers in Indian homes and offices
Digisol, from Smartlink in India, makes budget routers, ADSL modems, access points and network switches. Many broadband providers and local cable operators install Digisol routers for their customers.
Most open at 192.168.1.1 or 192.168.2.1 with admin/admin. If an operator installed it, they may have changed the password, so check with them before resetting.
Settings to change on a Digisol router
- Change the admin password from admin under System or Management.
- Set WiFi to WPA2-PSK with a strong password.
- If your provider uses PPPoE, note the username and password before you change anything.
- Turn off WPS.
- Check for firmware on Digisol’s support site.
Internet stops after a reset
If your internet stops working after resetting a Digisol router, the PPPoE login from your provider was probably wiped. Log in, open WAN or Internet settings, choose PPPoE and enter the username and password your provider gave you. If you don’t have them, call your local operator.
Digisol access points and switches
Digisol’s range also includes managed and unmanaged switches and ceiling access points used in offices and schools. Access points typically have their own login at a default address on the label.
Switches without a web interface just pass traffic and don’t need setup. If you’re unsure which device you have, check the model on the label and search Digisol’s support site.
Find your PPPoE details
- Check your welcome letter or email from your provider.
- Look in the router’s WAN settings before resetting; some routers show the username.
- Ask your local operator or ISP for the password.
- Write them down and keep them near the router.
