Comfast Router Login: Router Admin Setup Guide
Log in to Comfast at 192.168.10.1 with admin and admin. WiFi and reset.
Connect to your Comfast router first by WiFi or cable. Comfast extenders and outdoor CPEs use the same address.
Comfast routers, extenders, outdoor CPEs and USB adapters with AP mode open their settings at 192.168.10.1.
The default login is admin and admin. Here is how to log in, change WiFi and reset.
The fastest way in: tap the login button in the box at the top of this page, then sign in with the details on your router label.
How to log in to your Comfast router
- Connect your phone or computer to the router WiFi, or plug in an Ethernet cable.
- Open a browser and type http://192.168.10.1 in the address bar.
- Enter the username and password from the table below or the router label.
- Once logged in, change the admin password and use WPA2 or WPA3 for WiFi.
If the page does not open, check your Default Gateway with our Router IP Finder. ISP builds sometimes use a different address.
The gateway check is the step I take first when a Comfast page will not open.
Comfast default IP, username and password
| Model or type | Login address | Username | Password |
|---|---|---|---|
| Comfast routers (CF-WR series) | 192.168.10.1 | admin | admin |
| Comfast extenders | 192.168.10.1 | admin | admin |
| Outdoor CPE (CF-E series) | 192.168.10.1 | admin | admin |
Some newer units ask only for a password, which is admin by default. The password-only detail is the label fact I check first on a newer Comfast.
How to change the WiFi password on a Comfast router
- Log in at 192.168.10.1.
- Open Wireless settings.
- Change SSID and key with WPA2-PSK.
- Save and reconnect devices.
Outdoor CPEs also let you choose AP or client mode here. Need a strong key? Try our WiFi Password Generator. I change the key from the Wireless page before I touch anything else on a Comfast.
Comfast login problems and fixes
- 192.168.10.1 will not load: make sure you are on the router WiFi, not mobile data or a VPN, and type http:// in front.
- Wrong password: check the label first. If you or your ISP changed it, the defaults will not work.
- Page loads but login fails: clear the browser cache or try a private window. Some routers lock you out for a few minutes after several attempts.
- Router from your ISP: the provider may manage it. Their app or support line can reset the admin password.
- Still locked out: a factory reset restores the label login, but erases your settings.
I start with the label check whenever a Comfast login will not work.
How to reset a Comfast router
- Keep the router powered on.
- Press and hold the reset button for about 10 seconds, until the lights flash.
- Release and wait 2 to 3 minutes.
- Log in with the default details and set up WiFi again.
After a reset, reconfigure the operating mode if you used bridge or client mode. The 10-second hold is the timing I trust before I reach for a reset on a Comfast.
Which COMFAST device do you have?
COMFAST makes a wide range of affordable networking gear, and the login depends on the type:
- WiFi extenders and repeaters: usually 192.168.10.1, reached by joining the extender’s COMFAST_xxxx network.
- Outdoor CPE and bridges (CF-E series): often 192.168.10.1 or a similar address, used to link buildings.
- Routers and ceiling access points: 192.168.10.1 or 192.168.1.1, depending on the model.
- USB WiFi adapters: no login; they use a driver on your computer.
The extender-network detail is the one I mention first when the address looks unfamiliar.
Point-to-point bridges
COMFAST outdoor bridges are a cheap way to share internet between a house and a garage, office or second building. One unit is set as access point and the other as station (client). Keep a clear line of sight between them and aim them carefully for the best signal.
The line-of-sight warning is the bridge detail I flag first for any outdoor pair.
COMFAST USB adapters
COMFAST USB WiFi adapters are popular for adding WiFi to desktop PCs. Many work automatically on Windows 10 and 11. If yours doesn’t, install the driver from COMFAST’s site or the included disc. Dual-band models (with 5G or AC in the name) can connect to 5 GHz networks; single-band ones only see 2.4 GHz.
The driver-install step is the one I warn about first when a USB adapter will not show up.
Changing a COMFAST device’s IP
- Log in at the current address.
- Go to Network or LAN settings.
- Change the IP to one in your router’s range, outside the DHCP pool.
- Set the gateway to your router’s address.
- Save and reconnect at the new address.
The outside-the-DHCP-pool rule is the detail I check first before I move any address.
