Arris SBG6900-AC Login: IP, Password & Setup

Arris SBG6900-AC Default Login and Password I know the frustration: the Arris SBG6900-AC is online,…

Arris SBG6900-AC Default Login and Password

I know the frustration: the Arris SBG6900-AC is online, the Wi-Fi works, but the admin page will not take the password you are sure is right. I have been stuck on that screen myself, and the cause is usually a wrong default, not a broken gateway. The SBG6900-AC is a cable gateway, so its login lives at 192.168.0.1, and this guide gives you the correct defaults, the login steps, and the reset fix that works when nothing else does.

Log in to the Arris SBG6900-AC at 192.168.0.1 with the username admin and the password password. On later versions, the Wi-Fi Security Key printed on the bottom label is the admin password instead.

The fastest way in: tap the button below, then sign in with the details in the box.

🔐 Arris SBG6900-AC Admin Login

IP Address: 192.168.0.1

Username: admin

Password: password

SSID: SBG6900AC-XXXX

Login to Admin Panel →

This button opens our 192.168.0.1 guide, which takes you on to the router login page. It works only when your device is connected to this gateway, by WiFi or cable.

Arris SBG6900-AC Default Login Details

I checked these defaults against the SBG6900-AC user guide and ARRIS support pages before I wrote them down, so the table below matches the gateway you have in front of you.

The SBG6900-AC is a cable gateway, so it answers at 192.168.0.1 on most builds. Keep the defaults somewhere safe once you have logged in, and change the admin password to something only you know.

DetailValue
Login IP192.168.0.1
Usernameadmin
Passwordpassword
SSIDSBG6900AC-XXXX (on the bottom label)

How to Log In to the Arris SBG6900-AC

I walk through this in the same order every time, because the order is what keeps a login from going wrong. If your gateway came from an ISP, the Arris login guide covers the ISP label-password versions too.

  1. Connect your computer or phone to the SBG6900-AC with an Ethernet cable or over Wi-Fi. I use a cable for the first login, because a weak Wi-Fi signal can cut the page off halfway.
  2. Open a browser and go to 192.168.0.1. If Chrome or Edge shows a message that 192.168.0.1 uses an unsupported protocol, open the page in Firefox or Safari instead.
  3. Type admin in the username field and password in the password field. On later versions, type the Wi-Fi Security Key from the bottom label as the password instead.
  4. Click Log In. The Web Manager opens, and you can change the Wi-Fi name and password, check connected devices, or look at the gateway status.
Arris SBG6900-AC login ethernet cables plugged into a switch wifirouterzone.com
Connect to the SBG6900-AC by cable or Wi-Fi before you open the login page.

Default Username and Password — All Variants

I have seen this catch owners out: the same model can ask for a different password on another build, so check which case matches your gateway.

The SBG6900-AC most often uses admin with password as the password. Try the label key below before you reset anything:

VersionUsernamePassword
Most commonadminpassword
Later versionsadminWi-Fi Security Key (bottom label)

If neither works, check the label on the bottom of the gateway. Some ISP versions use their own credentials, and the label is the authority.

Change WiFi Password and Network Name

I change the Wi-Fi password first on every gateway I set up, because the factory password is the same on every unit that leaves the shop.

Once you are logged in to the SBG6900-AC Web Manager, changing the Wi-Fi details takes about a minute:

  1. Log in at 192.168.0.1 with the admin password.
  2. Open the Wireless settings section of the Web Manager.
  3. Pick the 2.4 GHz or 5 GHz primary network, then change the network name (SSID).
  4. Type a new Wi-Fi password, then save the settings.
  5. Reconnect your devices with the new password.

Use a password of at least 12 characters with a mix of letters and numbers, and avoid reusing a password you use anywhere else.

Login Not Working?

I start with the connection itself, because that is where most login failures begin, and I work through the list in the order it is written.

If the login page will not open or the password is rejected, work through these fixes:

  • Make sure your device is connected to the SBG6900-AC network, not to mobile data or a different Wi-Fi network.
  • Type the address exactly: 192.168.0.1, with no extra letters or spaces.
  • Try a different browser. ARRIS notes the unsupported-protocol error on Chrome, Edge, Firefox and Opera, and recommends Firefox or Safari for the Web Manager.
  • Check that Caps Lock is off, and type the password exactly as it is — passwords are case-sensitive.
  • Restart the gateway: unplug it, wait 30 seconds, and plug it back in.

If you still cannot log in because the password was changed and forgotten, reset the gateway to factory settings: press and hold the small Reset button on the back for about 10 seconds until the LEDs blink. After the reset, log in again with the factory defaults above, and set up the gateway from scratch.

Port forwarding is also set in the Web Manager once you are logged in. I only open the ports the device actually needs, and I close them again when the job is done.

Key specs: The Arris SBG6900-AC is a DOCSIS 3.0 cable gateway with 16×4 channel bonding, AC1900 dual-band Wi-Fi up to 1900 Mbps, and four Gigabit Ethernet ports.

FAQs About arris sbg6900-ac login

The default username is admin and the default password is password, at the login IP 192.168.0.1. On later versions the Wi-Fi Security Key printed on the bottom label is the admin password instead.

Connect to the gateway, open a browser, go to 192.168.0.1, and enter admin as the username and password as the password. I always connect by cable for the first login, because a weak Wi-Fi signal can cut the page off halfway.

Most often the device is not connected to the gateway, or the address was typed wrong. Connect to the SBG6900-AC network, type 192.168.0.1 exactly, try another browser, and restart the gateway if the page still does not load.

Press and hold the small Reset button on the back for about 10 seconds until the LEDs blink. A factory reset erases every setting, including the Wi-Fi name and password, so you will need to set the gateway up again and log in with the factory defaults.

The team behind this guide
Omar Haddad

Omar Haddad found this topic
Keyword Analyst
Focus: Search Data & Demand

Priya Sharma

Priya Sharma wrote this guide
Content Writer · Published November 16, 2026
Focus: Broadband & ISP Guides

Nina Petrova

Nina Petrova designed the visuals
Graphic Designer
Focus: Brand & Illustrations

Awais

Awais verified the facts
Founder & Editor-in-Chief · Last verified: November 2026
Focus: Final fact-check & publishing

Similar Posts