Actiontec C3000A Login: IP, Password & Setup
Actiontec C3000A Default Login and Password I know the scene: the CenturyLink C3000A is online,…
Actiontec C3000A Default Login and Password
I know the scene: the CenturyLink C3000A is online, the Wi-Fi works, but the admin page will not accept the password you typed. I have been stuck on that screen myself, and the fix is usually reading the right line on the sticker, not a broken gateway. The C3000A is a DSL gateway, so its login lives at 192.168.0.1, and this guide gives you the correct defaults, the login steps, and the reset fix that works when nothing else does.
Log in to the Actiontec C3000A at 192.168.0.1 with the username admin and the Admin Password printed on the gateway label. There is no single fixed factory password for this model — the label is the password.
The fastest way in: tap the button below, then sign in with the details in the box.
IP Address: 192.168.0.1
Username: admin
Password: Admin Password (on label)
SSID: CenturyLinkXXXX
Login to Admin Panel →This button opens our 192.168.0.1 guide, which takes you on to the router login page. It works only when your device is connected to this gateway, by WiFi or cable.
Actiontec C3000A Default Login Details
I checked these defaults against the C3000A manual and CenturyLink setup guides before I wrote them down, so the table below matches the gateway you have in front of you.
The C3000A is a CenturyLink DSL gateway, so it answers at 192.168.0.1 on most builds. Keep the label password somewhere safe once you have logged in, and change the admin password to something only you know.
| Detail | Value |
|---|---|
| Login IP | 192.168.0.1 |
| Username | admin |
| Password | Admin Password (on the label) |
| SSID | CenturyLinkXXXX (on the bottom label) |
How to Log In to the Actiontec C3000A
I walk through this in the same order every time, because the order is what keeps a login from going wrong. If your gateway came from CenturyLink, the Actiontec login guide covers the other ISP versions too.
- Connect your computer or phone to the C3000A with an Ethernet cable or over Wi-Fi. I use a cable for the first login, because a weak Wi-Fi signal can cut the page off halfway.
- Open a browser and go to 192.168.0.1. If that address does not open the login page, try 192.168.1.1, which some C3000A units answer on instead.
- Type admin in the username field and the Admin Password from the label in the password field. The admin password is a different line from the Wi-Fi key, so read the label carefully.
- Click Log In or Apply. The admin page opens, and you can change the Wi-Fi name and password, check connected devices, or look at the gateway status.

Default Username and Password — All Variants
I have seen this catch owners out: the same model can ask for a different password on another build, so check which case matches your gateway.
The C3000A most often uses admin with the Admin Password from the label. Try the blank-password case below before you reset anything:
| Version | Username | Password |
|---|---|---|
| Most common | admin | Admin Password (label) |
| Some units | admin | (blank — leave empty) |
If neither works, check the label on the bottom of the gateway. The C3000A manual points to the sticker for the credentials, so the label is the authority.
Change WiFi Password and Network Name
I change the Wi-Fi password first on every gateway I set up, because the factory password is the same on every unit that leaves the shop.
Once you are logged in to the C3000A admin page, changing the Wi-Fi details takes about a minute:
- Log in at 192.168.0.1 with the admin password from the label.
- Open the Wireless Setup section of the admin page.
- Pick the 2.4 GHz or 5 GHz network, then change the network name (SSID).
- Type a new Wi-Fi password, then save the settings.
- Reconnect your devices with the new password.
Use a password of at least 12 characters with a mix of letters and numbers, and avoid reusing a password you use anywhere else. You can also press the WPS button on the front to connect a device without typing the password.
Login Not Working?
I start with the connection itself, because that is where most login failures begin, and I work through the list in the order it is written.
If the login page will not open or the password is rejected, work through these fixes:
- Make sure your device is connected to the C3000A network, not to mobile data or a different Wi-Fi network.
- Type the address exactly: 192.168.0.1, with no extra letters or spaces. Some units answer at 192.168.1.1 instead.
- Check the label again: the Admin Password is not the Wi-Fi key, and the two lines sit close together on the sticker.
- Try a different browser, or clear the browser cache and try again.
- Restart the gateway: unplug it, wait 30 seconds, and plug it back in.
If you still cannot log in because the password was changed and forgotten, reset the gateway to factory settings: press a paperclip into the recessed Reset button on the rear panel and hold about 10 seconds until the LEDs flash. After the reset, log in again with the factory defaults above, and set up the gateway from scratch.
If you use your own router behind the C3000A, bridge mode (IP Passthrough) is in the admin page too. I leave it off unless a second router needs to handle the Wi-Fi.
Key specs: The Actiontec C3000A is a CenturyLink DSL gateway with bonded VDSL2, dual-band 802.11ac Wi-Fi up to 2.3 Gbps, four Gigabit Ethernet ports, and a USB 3.0 port.










