Converge Router Login: IP, Username and Password
Log in to Converge at 192.168.1.1 with the user login on the label. WiFi change and reset.
Connect to your Converge router first by WiFi or cable. Some Converge units use 192.168.0.1.
Converge FiberX modems in the Philippines, from ZTE, FiberHome and Huawei, open their settings at 192.168.1.1. A few models use 192.168.0.1. Huawei ONTs open at 192.168.100.1 instead, with root and adminHW as the login. The super-admin account on those ONTs is telecomadmin with the password admintelecom.
The user login is printed on the label, and the full admin account is usually kept by Converge. Here is how to log in, change WiFi and fix common errors.
The fastest way in: tap the login button in the box at the top of this page, then sign in with the details on your router label.
How to log in to your Converge router
- Connect your phone or computer to the router WiFi, or plug in an Ethernet cable.
- Open a browser and type http://192.168.1.1 in the address bar. If it does not load, try http://192.168.0.1.
- Enter the username and password from the table below or the router label.
- Once logged in, change the admin password and use WPA2 or WPA3 for WiFi.
If the page does not open, check your Default Gateway with our Router IP Finder. ISP builds sometimes use a different address.
The 192.168.1.1 address is the one I try first on any Converge that will not open.
Converge default IP, username and password
| Device | Login address | Username | Password |
|---|---|---|---|
| ZTE F670L / F660 | 192.168.1.1 | user | On the label |
| FiberHome HG6145 | 192.168.1.1 | user or admin | On the label |
| Other Converge units | 192.168.0.1 | admin | admin or label |
If the label login fails, Converge may have changed it. Call their hotline for help. The hotline-first route is the one I point at for a changed Converge login.
How to change the WiFi password on a Converge router
- Log in at 192.168.1.1.
- Open Network, WLAN, then WLAN Security or SSID Settings.
- Set WPA2-PSK and a new passphrase.
- Apply and reconnect devices.
Change both the 2.4 GHz and 5 GHz networks. Need a strong key? Try our WiFi Password Generator. For me, the both-bands step is the one I never skip on a Converge change.
Converge login problems and fixes
- 192.168.1.1 will not load: make sure you are on the router WiFi, not mobile data or a VPN, and type http:// in front.
- Wrong password: check the label first. If you or your ISP changed it, the defaults will not work.
- Page loads but login fails: clear the browser cache or try a private window. Some routers lock you out for a few minutes after several attempts.
- Router from your ISP: the provider may manage it. Their app or support line can reset the admin password.
- Still locked out: a factory reset restores the label login, but erases your settings.
I start with the label check whenever a Converge login will not work.
How to reset a Converge router
- Keep the router powered on.
- Press and hold the reset button for about 10 seconds, until the lights flash.
- Release and wait 2 to 3 minutes.
- Log in with the default details and set up WiFi again.
Converge fiber usually reconnects automatically after a reset. The 10-second hold is the timing I trust before I reach for a reset on a Converge.
Keep your Converge WiFi fast
- Change the WiFi password from the default on the sticker.
- Rename the 5 GHz network so you can connect phones and laptops to it when close by.
- Place the modem in an open, central spot rather than near the door where the fibre enters.
- Restart the modem if speeds drop, and check the LOS light if internet goes down.
- If one area is weak, add a mesh system in access point mode.
The 5-GHz rename is the speed tip I reach for first on any Converge home. On the sticker, the WiFi password is listed as the WLAN Key.
Red LOS light on Converge
A red LOS light means the modem isn’t receiving the fibre signal. Check the fibre cable for sharp bends or a loose connector, then restart. If it stays red, report it through Converge’s support channels so a technician can check the line.
The red-LOS case is the one I act on first when a Converge modem looks dead.
Converge FiberX plans and WiFi speed
On higher FiberX plans, the modem’s WiFi can be the bottleneck, especially in bigger homes. Speeds near the modem on 5 GHz should be close to your plan; further away, they drop. A WiFi 6 mesh system in access point mode helps if your plan is fast and your home is large or has concrete walls.
The modem-bottleneck detail is the one I explain first on a faster FiberX plan.
See who is using your Converge WiFi
- Log in to the modem with the sticker details.
- Open the device list, often under Status, LAN or WLAN.
- Check for devices you don’t recognise.
- Change your WiFi password to remove them.
The device-list check is the step I take first when unknown devices show up.
