Ziggo Modem Login: 192.168.178.1 and Password
Log in to Ziggo at 192.168.178.1 with the label password. WiFi, bridge mode and reset.
Connect to your Ziggo router first by WiFi or cable. Ziggo Connectbox and SmartWifi modem use the same address.
Ziggo Connectbox and SmartWifi modems in the Netherlands open their settings at 192.168.178.1.
The modem password is printed on the label, often listed as the modem or admin password. Here is how to log in, change WiFi and turn on bridge mode.
The fastest way in: tap the login button in the box at the top of this page, then sign in with the details on your router label.
How to log in to your Ziggo router
- Connect your phone or computer to the router WiFi, or plug in an Ethernet cable.
- Open a browser and type http://192.168.178.1 in the address bar.
- Enter the username and password from the table below or the router label.
- Once logged in, change the admin password and use WPA2 or WPA3 for WiFi.
If the page does not open, check your Default Gateway with our Router IP Finder. ISP builds sometimes use a different address.
The 192.168.178.1 address is the one I try first on any Ziggo that will not open.
Ziggo default IP, username and password
| Device | Login address | Username | Password |
|---|---|---|---|
| Ziggo Connectbox (Compal) | 192.168.178.1 | None or admin | On the label |
| Ziggo SmartWifi modem (Sagemcom) | 192.168.178.1 | admin | On the label |
| Older Ziggo modems | 192.168.178.1 or 192.168.1.1 | admin | On the label |
The Connectbox asks only for a password on most firmware. The password-only detail is the label fact I check first on a Ziggo.
How to change the WiFi password on a Ziggo router
- Log in at 192.168.178.1.
- Open Wireless or WiFi.
- Change the name and key and save.
- Reconnect devices.
The Mijn Ziggo app can also manage WiFi. Need a strong key? Try our WiFi Password Generator. For me, the Wireless page is where every Ziggo WiFi change starts.
Ziggo bridge mode
To use your own router, open Modem Mode or Bridge Mode in the admin page, or switch it in Mijn Ziggo. The modem then hands its public IP to your router. The bridge-mode-first step is the one I take before I plug a second router in.
Ziggo login problems and fixes
- 192.168.178.1 will not load: make sure you are on the router WiFi, not mobile data or a VPN, and type http:// in front.
- Wrong password: check the label first. If you or your ISP changed it, the defaults will not work.
- Page loads but login fails: clear the browser cache or try a private window. Some routers lock you out for a few minutes after several attempts.
- Router from your ISP: the provider may manage it. Their app or support line can reset the admin password.
- Still locked out: a factory reset restores the label login, but erases your settings.
I start with the label check whenever a Ziggo login will not work.
How to reset a Ziggo router
- Keep the router powered on.
- Press and hold the reset button for about 30 seconds, until the lights flash.
- Release and wait 2 to 3 minutes.
- Log in with the default details and set up WiFi again.
The modem needs several minutes to reconnect after a reset. The 30-second hold is the timing I trust before I reach for a reset on a Ziggo.
Ziggo modem models
Ziggo in the Netherlands has supplied several modems: the Connectbox, the Ziggo Giga modem and newer SmartWiFi modems. Most open at 192.168.178.1, with the password printed on the label on the bottom. Older Technicolor TC7210 modems list the wireless details under ‘draadloos’ on the label.
Many settings can also be managed in the Ziggo app or via Mijn Ziggo, including WiFi name and password. The app-manageable detail is the one I mention first for any Ziggo modem.
Using your own router with Ziggo
Ziggo modems support bridge mode, which turns off the modem’s router and WiFi so your own router takes over.
- Log in to Mijn Ziggo.
- Go to your internet settings and choose to enable bridge mode (or modem mode).
- Wait for the modem to restart.
- Connect your router’s WAN port to the modem’s first LAN port.
In bridge mode, the modem’s own WiFi switches off completely. Make sure your router is ready before you switch.
The WiFi-off warning is the bridge-mode detail I flag first for any Ziggo owner.
SmartWiFi pods
Ziggo offers SmartWiFi pods for better coverage. They work with Ziggo’s modem in router mode and are managed in the Ziggo app. If you use bridge mode with your own router, the pods won’t work, so use your own mesh instead.
The router-mode-only detail is the Pod limit I explain first to Ziggo owners.
