Bell Home Hub Login: IP and Admin Password
Log in to Bell Home Hub at 192.168.2.1 with the serial number as password. WiFi, DMZ and reset.
Connect to your Bell router first by WiFi or cable. Bell Home Hub and Giga Hub use the serial number as the first password.
Bell Home Hub 3000, Home Hub 4000 and Giga Hub modems in Canada open their settings at 192.168.2.1, also reachable as http://home on many units.
On first login the admin password is usually the modem serial number (S/N) printed on the label, and you are asked to set a new one. You can also manage WiFi in the MyBell app.
The fastest way in: tap the login button in the box at the top of this page, then sign in with the details on your router label.
How to log in to your Bell router
- Connect your phone or computer to the modem WiFi, or plug in an Ethernet cable.
- Open a browser and type http://192.168.2.1 in the address bar. You can also try http://home.
- Enter the admin username and password from the label or the table below.
- Once logged in, change the admin password and check that WiFi security is WPA2 or WPA3.
If the page does not open, check your Default Gateway with our Router IP Finder. ISP builds sometimes use a different address.
The http://home shortcut is the address I try first when 192.168.2.1 will not open on a Bell. Bell’s bell.ca/mymodem shortcut opens the same page.
Bell default IP, username and password
| Device | Login address | Username | Password |
|---|---|---|---|
| Home Hub 3000 / 4000 | 192.168.2.1 | admin | Serial number (S/N) first time |
| Giga Hub | 192.168.2.1 | admin | Serial number first time |
| Older Bell modems | 192.168.2.1 | admin | admin |
| After setup | 192.168.2.1 | admin | Your own password |
If the serial number does not work, the password was already changed. Reset the hub to restore it. On a Bell hub, the serial number is the first thing I check when the defaults fail.
How to change the WiFi password on a Bell router
- Log in at 192.168.2.1.
- Open Wi-Fi or Wireless settings.
- Change the network name and password for each band, or the unified network.
- Save and reconnect your devices.
The MyBell app can also change WiFi from your phone. Need a strong key? Try our WiFi Password Generator. For me, the MyBell app is the quickest way to change a WiFi password on a Bell.
Using your own router with Bell
Bell hubs do not offer a simple bridge mode, but you can turn on Advanced DMZ under Advanced Tools and Settings, then point it at your own router. Your router then receives the public IP and handles WiFi.
Turn off the hub WiFi afterwards to avoid interference. The DMZ-first step is the one I take before I plug a second router into a Bell hub.
Bell login problems and fixes
- 192.168.2.1 will not load: make sure you are on the router WiFi, not mobile data or a VPN, and type http:// in front.
- Wrong password: check the label first. If you or your ISP changed it, the defaults will not work.
- Page loads but login fails: clear the browser cache or try a private window. Some routers lock you out for a few minutes after several attempts.
- Router from your ISP: the provider may manage it. Their app or support line can reset the admin password.
- Still locked out: a factory reset restores the label login, but erases your settings.
When a Bell login will not work, the label is where I start.
How to reset a Bell router
- Keep the modem powered on.
- Press and hold the reset button for about 10 seconds.
- Release and wait several minutes while it restarts and reconnects.
- Log in with the label details and set up WiFi again.
Bell may push its settings back after a reset. Keep your Bell internet username handy for PPPoE setups. I give the hub a full few minutes to come back before I try logging in again.
Bell Wi-Fi Pods and the Bell Wi-Fi app
Bell offers Wi-Fi Pods to extend Home Hub coverage. They’re added and managed through the Bell Wi-Fi app, which also shows connected devices, lets you pause access and runs speed tests. Place pods roughly halfway between the hub and the area you want to cover.
My first stop is the Bell Wi-Fi app whenever a pod will not show up.
Find your Bell admin password
- Look at the sticker on the back or bottom of the Home Hub.
- Find the serial number (S/N). On many hubs, that’s the default admin password.
- If it doesn’t work, someone changed it. Check your password manager.
- If it’s lost, reset the hub with the reset button and use the serial number again.
The serial-number sticker is the first thing I look for on any Bell hub.
