SonicWall TZ 105W Login: Default Password

Open the SonicWall TZ 105W admin panel over HTTPS, connect by cable to a LAN port first, and fix the login faults that keep owners out today.

SonicWall TZ 105W Default Login and Password

I know the scene: the SonicWall TZ 105W is online, the lights are up, but the admin page will not take the password you are sure is right. The fix is usually the address, not the password. The TZ 105W is a firewall appliance, so its login lives at 192.168.168.168, and this guide gives you the correct defaults, the first-time setup wizard, and the reset fix that works when nothing else does.

This guide gives you the TZ 105W login, the setup wizard steps, and the fixes that get you in.

Log in to the SonicWall TZ 105W at https://192.168.168.168 with the username admin and the password password. Connect by cable to a LAN port first, and change the password the first time the setup wizard asks you to.

The fastest way in: tap the button below, then sign in with the details in the box.

🔐 SonicWall Router Admin Login

IP Address: 192.168.168.168

Username: admin

Password: password

SSID: — (set during setup)

Login to Admin Panel →

This button opens the TZ 105W login page directly at 192.168.168.168. It works only when your computer is connected to a LAN port on the appliance by cable, and your computer needs an address on the 192.168.168.x network. There is no matching guide on our site for this address yet, so the button goes straight to the appliance.

SonicWall TZ 105W Default Login Details

I checked these defaults against SonicWall’s own TZ series getting started guide and the TZ 105/205 quick start guide before I wrote them down, so the table below matches the appliance you have in front of you.

The TZ 105W is a UTM firewall appliance, so it answers at 192.168.168.168 on its LAN interface. Keep the defaults somewhere safe once you have logged in, and change the admin password the first time the setup wizard asks — the wizard prompts you for it.

DetailValue
Login IP192.168.168.168 (HTTPS)
Usernameadmin
Passwordpassword
SSID— (wireless N, set during setup)
Management pagehttps://192.168.168.168

How to Log In to the SonicWall TZ 105W

If 192.168.168.168 does not open the login page, our Router IP Finder walks you through finding the right address for your network.

  1. Connect your computer to a LAN port on the TZ 105W (X0, X2, X3 or X4) with an Ethernet cable. Use a cable for the first login — wireless access to the admin page is off by default on many SonicWall units.
  2. Wait a minute or two for the appliance to finish booting, then let your computer pick up an address from the TZ 105W, or set one by hand in the 192.168.168.x range, such as 192.168.168.20.
  3. Open a browser and go to https://192.168.168.168. The SonicWall management login page appears.
  4. Type admin in the username field and password in the password field, then click Login.
  5. On a first login, the setup wizard offers to walk you through the setup. Change the admin password when it asks, pick your time zone, and register the appliance at MySonicWall.
SonicWall TZ 105W login woman working on laptop by office window wifirouterzone.com
Connect by cable to a LAN port before you open the login page.

Default Username and Password — All Variants

I have seen this catch owners out: the same appliance can ask for a different password on another build, so check which case matches your TZ 105W.

The TZ 105W most often uses admin with password as the password. Try the other case below before you reset anything:

VersionUsernamePassword
Most common (SonicWall docs)adminpassword
Some units / after setupadminpassword you set in the wizard

SonicWall’s own guides are consistent on this one: admin and password is the factory default for every TZ appliance, and the wizard makes you change it at first setup. If password fails, the appliance was already set up once — and only a reset brings the factory login back.

Change SonicWall TZ 105W WiFi Password and Network Name

The W in TZ 105W means wireless, so this model has a Wi-Fi radio the plain TZ 105 lacks. I change the wireless password first on every appliance I set up, because the factory settings are the same on every unit that leaves the shop.

Once you are logged in to the SonicOS management page, changing the wireless details takes a few minutes:

  1. Log in at https://192.168.168.168 with the admin password.
  2. Open Network, then Wireless, in the SonicOS menu.
  3. Pick the wireless network, then change the network name (SSID) to something of your own.
  4. Set the security to WPA2, type a new Wi-Fi password, then save the settings.
  5. Reconnect your devices with the new password, starting with the computer in front of you.

Use a password of at least 12 characters with a mix of letters and numbers, and avoid reusing a password you use anywhere else. If the Wireless menu is missing, your unit may be a plain TZ 105 without the radio — check the model on the label.

SonicWall TZ 105W Login Not Working?

If the login page will not open or the password is rejected, work through these fixes:

  • Make sure your computer is on a LAN port (X0, X2, X3 or X4), not the WAN port (X1) and not on Wi-Fi.
  • Check that your computer has an address in the 192.168.168.x range. If it picked up a different address, set one by hand, such as 192.168.168.20.
  • Type the address exactly: https://192.168.168.168, with no extra letters or spaces.
  • Remember the password is password, not admin. That one difference is the most common reason the login fails.
  • Wait for the appliance to finish booting. A TZ 105 takes a couple of minutes after power-on before the login page answers.

If you still cannot log in because the password was changed and forgotten, reset the router to factory settings: press the reset button on the back with a paper clip and hold it until the status lights change, then let the appliance restart and log in again with admin and password.

A reset also wipes the wireless settings and any rules you added, so you will need to run the setup wizard again. If you changed the admin password in the wizard and forgot it, a reset is the only way back in — there is no password recovery on a TZ appliance. If the login page will not open at all, check our forgot router password guide for the next steps.

Key specs: The SonicWall TZ 105W is a UTM firewall appliance with SonicOS, five Ethernet ports (X0 LAN, X1 WAN, X2–X4 LAN), wireless N, a console port, and a 12V power supply. SonicWall ended support for the TZ 105 in July 2020, so it gets no new firmware — plan a move to a newer TZ model if you need current protection.

SonicWall TZ 105W problems users report, and what fixed them

Forgot the admin password and the light blinks

A TZ 105W owner on the SonicWall community could not log in. Support staff pointed to safe mode at 192.168.168.168 on the X0 port, with factory defaults admin and password.

Safe mode page will not open

SonicWall notes safe mode works only over HTTP, so type http:// in full or the browser jumps to https and fails. See SonicWall: accessing safe mode.

Out of support

SonicWall no longer supports the TZ 105W, as its community staff noted. You can still reset it through safe mode, but no new firmware or security fixes are coming.

FAQs About sonicwall tz 105w apl22 09c login

Log in at https://192.168.168.168 with the username admin and the password password. That is SonicWall’s own factory default for every TZ appliance, and the setup wizard makes you change it at first login.

The TZ 105W answers at 192.168.168.168 on its LAN interface, and that is the address the quick start guide prints. Connect by cable to a LAN port first, and give your computer an address in the 192.168.168.x range if it does not pick one up.

The most common cause is a password set during an earlier setup — the wizard changes it the first time it runs. If you did not set one, try admin and password again, and check that Caps Lock is off. If it still fails, a factory reset is the only way back in.

Log in at https://192.168.168.168, open Network, then Wireless, pick the network, and type a new Wi-Fi password. Save the settings, then reconnect your devices with the new password.

Press the reset button on the back with a paper clip and hold it until the status lights change, then let the appliance restart. A reset restores the factory login of admin and password, and you will need to run the setup wizard again.

The team behind this guide
Grace Muller

Grace Muller found this topic
Content Strategist
Focus: Topic Planning & Coverage

Sarah Mitchell

Sarah Mitchell wrote this guide
Senior Content Writer · Published November 21, 2026
Focus: Router Login Guides

Nina Petrova

Nina Petrova designed the visuals
Graphic Designer
Focus: Brand & Illustrations

Awais

Awais verified the facts
Founder & Editor-in-Chief · Last verified: November 2026
Focus: Final fact-check & publishing

Similar Posts