Wavlink Login: wifi.wavlink.com and 192.168.10.1
Log in to Wavlink at wifi.wavlink.com or 192.168.10.1 with admin and admin.
Connect to your Wavlink router first by WiFi or cable. You can also use wifi.wavlink.com.
Wavlink routers and range extenders open their settings at 192.168.10.1 or http://wifi.wavlink.com. Some extenders use 192.168.20.1 or ap.setup.
The default login is usually admin with the password admin, or you set it during setup. Here is how to log in, change WiFi and reset.
The fastest way in: tap the login button in the box at the top of this page, then sign in with the details on your router label.
How to log in to your Wavlink router
- Connect your phone or computer to the router WiFi, or plug in an Ethernet cable.
- Open a browser and type http://192.168.10.1 in the address bar. Or open http://wifi.wavlink.com.
- Enter the username and password from the table below or the router label.
- Once logged in, change the admin password and use WPA2 or WPA3 for WiFi.
If the page does not open, check your Default Gateway with our Router IP Finder. ISP builds sometimes use a different address.
The wifi.wavlink.com address is the one I try first on any Wavlink that will not open.
Wavlink default IP, username and password
| Model or type | Login address | Username | Password |
|---|---|---|---|
| Wavlink routers | 192.168.10.1 or wifi.wavlink.com | admin | admin |
| Wavlink extenders | wifi.wavlink.com or 192.168.10.1 | admin | admin or set at setup |
| Outdoor and AC units | Label | admin | admin |
Some models ask only for a password, which is admin by default. The password-only-model detail is the one I mention first for a Wavlink login.
How to change the WiFi password on a Wavlink router
- Log in at wifi.wavlink.com.
- Open Wireless settings.
- Change the name and password and save.
- Reconnect devices.
Extenders follow the main router WiFi unless you set a custom name. Need a strong key? Try our WiFi Password Generator. For me, the Wireless page is where every Wavlink WiFi change starts.
Wavlink login problems and fixes
- 192.168.10.1 will not load: make sure you are on the router WiFi, not mobile data or a VPN, and type http:// in front.
- Wrong password: check the label first. If you or your ISP changed it, the defaults will not work.
- Page loads but login fails: clear the browser cache or try a private window. Some routers lock you out for a few minutes after several attempts.
- Router from your ISP: the provider may manage it. Their app or support line can reset the admin password.
- Still locked out: a factory reset restores the label login, but erases your settings.
I start with the label check whenever a Wavlink login will not work.
How to reset a Wavlink router
- Keep the router powered on.
- Press and hold the reset button for about 10 seconds, until the lights flash.
- Release and wait 2 to 3 minutes.
- Log in with the default details and set up WiFi again.
Run setup again after a reset. The 10-second hold is the timing I trust before I reach for a reset on a Wavlink.
Wavlink extenders, routers and adapters
Wavlink makes budget extenders, outdoor access points, routers and USB adapters. Extenders and many routers use 192.168.10.1 or the address wifi.wavlink.com during setup. You connect to the device’s own network (often named WAVLINK-N or similar) first.
Most models ask you to set a login password the first time, while older ones use admin. The set-at-first-setup detail is the one I warn about first on any Wavlink.
Firmware and support
Wavlink posts firmware on its website by model. Updating can fix connection drops, but check the exact model and hardware version first. If an extender keeps losing connection, try updating before replacing it. The exact-model check is the step I never skip before I flash any Wavlink firmware.
Extender, access point or router mode on Wavlink
Many Wavlink devices can run in several modes, chosen during setup or in the web page:
- Repeater: picks up your existing WiFi and rebroadcasts it. Easiest, but speed drops with distance.
- Access point: connect it to your router with a cable and it creates strong WiFi with no speed loss.
- Router: plug a modem into it and it runs your whole network.
- WISP or client: on outdoor models, joins a distant network and shares it over Ethernet.
If you can run a cable, access point mode beats repeater mode every time. The cable-first rule is the setup I fall back on for any Wavlink extender.
Wavlink extender keeps dropping
- Move it one room closer to the router; the signal light should show good or excellent.
- Update firmware from Wavlink’s site for your exact model.
- Set your router’s 2.4 GHz channel to 1, 6 or 11 so the extender has less interference.
- Avoid plugging it behind furniture or into a power strip on the floor.
- Reset and set it up again if it was configured for an old router.
The one-room-closer move is the fix I try first when a Wavlink extender drops.
